DC 5V-30V MOS Trigger Cycle Timer Delay Board Switch Turn On/Off Relay Module

$5.32 Buy It Now or Best Offer
free,30-Day Returns

Seller Store ecbuying
(1559) 99.8%,

Location: shenzhen
Ships to: US,
Item: 295806090910

Return shipping will be paid by:Buyer
All returns accepted:Returns Accepted
Item must be returned within:30 Days
Refund will be given as:Money Back
MPN:Does Not Apply
Item Length:N/A
Smart Home Compatibility:N/A
Suitable For:N/A
Current Type:DC
Unit Type:Unit
Number in Pack:1
Item Height:N/A
Contact Material:N/A
Features:convenient,simple
Unit Quantity:1
Finish:N/A
Item Width:N/A
Protection Properties:N/A
Color:Black
Current Rating:N/A
California Prop 65 Warning:No
Unbranded:Unbranded
Operation Method:N/A
Type:delay module
Coil Voltage:N/A
N/A:N/A
Country/Region of Manufacture:China
Resistance Properties:N/A
Smart Home Protocol:N/A
Application:N/A

Usage: 1. To achieve fast turn-on and off the circuit, an unlimited number of switching; 2. Conducting and cutting process does not produce noise, no spark, no electromagnetic interference; 3. Compared with electromagnetic MOS switch products, longer life; 4. The dual-MOS parallel drive, lower resistance, more current, strong power; at room temperature, operating current of up to 15A, power up to 400W, to meet the most use of the equipment; 5. A method for controlling the motor, lights, LED, DC motors, micro-pumps, solenoid valves, etc., very convenient. Feature: 1. Wide voltage input (5 -30V), most devices can be used, very convenient; 2. The interface is clear and simple, powerful, easy to understand, meet almost all your needs; 3. The emergency stop function (”STOP” key); With reverse polarity protection, reverse polarity will not burn the product. 4. Increase the sleep mode, if this mode is enabled, without any operation within 3 minutes, then automatically turn off the monitor, any key wake-up; 5. You can set a different OP, CL, LOP、CLL、CLH、SP parameters, which are independent of each other, and are automatically saved; 6. New addition of Tik Tok automatic slide screen function. 7. New serial communication function, easy to read and set parameters. 8. After the module is powered down, all parameter settings are not lost. Operating mode: Mode without triggering P00: After the module is powered on, the MOS switch is powered off for CL time, and the MOS switch is started P01: After the module is powered on, the MOS switch is on OP time and the MOS switch is disconnected P02: After power on, there is no need to trigger the signal, the OP time of the MOS switch on, the CL time of the MOS switch off, and the above actions can be cycled; the number of cycles (LOP) can be set; after the cycle, the MOS switch is kept disconnected P03: After power on, there is no need to trigger the signal, the CL time of the MOS switch is disconnected, the OP time of the MOS switch is on, and the above actions are cycled; the number of cycles (LOP) can be set; after the cycle, the MOS switch is kept on Patterns that need to be triggered P04: After the signal is triggered, the MOS switch turns on the OP time and then turns off; within the OP time, the signal is triggered again and is invalid P05: After the signal is triggered, the MOS switch conducts OP time and then disconnects. Within the OP time, the signal is triggered again to restart the timing P06: After the signal is triggered, the MOS switch conducts OP time and then disconnects. Within OP time, the signal triggers the reset again, the MOS switch disconnects, and the timing stops P07: After the signal is triggered, the MOS switch opens CL time, and then the MOS switch is on P08: After the signal is triggered, the CL time of the MOS switch is disconnected, and the OP time of the MOS switch is on. After the timing is completed, the MOS switch is disconnected; in the cycle, the signal trigger is invalid P09: After the signal is triggered, the CL time of the MOS switch is disconnected, and the OP time of the MOS switch is on. After the timing is completed, the MOS switch is disconnected; in the cycle, the signal is triggered again, and the timing is repeated P10: After the signal is triggered, the CL time of the MOS switch is disconnected, and the OP time of the MOS switch is on, and then the above actions are cycled. In the cycle, the signal is given again to restore the initial state and stop timing; the number of cycles (LOP) can be set; at the end of the cycle, the MOS switch is kept on P11: After the signal is triggered, the OP time of the MOS switch is on, the CL time of the MOS switch is disconnected, and then the above actions are cycled. In the cycle, the signal is given again to restore the initial state and stop timing; the number of cycles (LOP) can be set; at the end of the cycle, the MOS switch is kept disconnected P12: After the signal is triggered, MOS switch conducts OP time, MOS switch disconnects CL time, and then circulates the above action. The signal is given again in the loop, which is invalid. Looping times (LOP) can be set; Loop ends and the holding MOS switch is disconnected P13: Signal holding function: if there is a trigger signal, the timing is cleared to zero, and the MOS switch remains on; when the signal disappears, the MOS switch is disconnected after timing OP; during timing, if there is another signal, the timing is cleared P14: Signal holding function: if there is a trigger signal, the timing will be cleared and the MOS switch will remain disconnected; when the signal disappears, the MOS switch will be turned on after timing CL; during the timing period, if there is another signal, the timing will be cleared Tik Tok auto slide mode P15: After the signal is triggered, the MOS switch is disconnected for L -h time (for example, L= 10, H = 15, then the MOS switch disconnection time is a random number between 10-15 seconds, L and H are set at 0.0-99.9 seconds, and H is greater than or equal to L). After the MOS switch disconnection time is over, the motor can be driven to rotate at the speed sp (frequency 600 Hz, gear 0-16 corresponding to duty cycle 20, 25, 30,… 100 respectively) Parameter: Operating voltage: DC 5V -30V Continuous current 15A Max 30A Output power: 400W Quiescent Current: 20mA Operating Current: 50mA Life: any switching times Working temperature: -40-85℃ Size:60*34*12mm With optocoupler isolation, enhanced anti-jamming capability, industrial grade board. Pay attention: 1. The module is an active output, the output voltage equal to the input voltage(DC 5V-30V). 2.’DC + ’and’ load + ’This is an internal short circuit of the poles, but’ DC- ’and’ load – ’poles during use can not be shorted, otherwise the load can not be controlled on and off, which is equivalent load is been carrying electricity. Timing range: 0.1 seconds (min) to 999 minutes (max) continuously adjustable How to choose the time range? After setting the mode selection screen parameter value by a short press ”STOP” button to select the time range; XXX. decimal point in the unit place, time range: 1 second to 999 seconds. XX. X decimal point in decade place, Timing range: 0.1 seconds to 99.9 seconds X. X. X. decimal full brightness, Timing range: 1 minute to 999 minutes. For example, you want to set ”OP” is 3.2 seconds, then move the decimal point to decade place, the digital display 03.2 Parameter description: ”OP” – conduction time, ”CL” – off time, ”LOP” – the number of cycles (1-999 times, ”—” represents infinite loop). These parameters are independent of each other, but is shared by each mode. For example, in P1 mode, set the on-time ”OP” is 5 seconds, if you switch to P2 mode, it’s ”OP” will be 5 seconds too. In the main interface (display 000), short press ”SET” button will display ”OP” ( ”CL”, ”LOP”) and the corresponding time XXX; Some parameters only mode ”OP” (such as the mode P1), short press the ”SET” key to display only the ”OP” and the corresponding time; Some models have parameters ”OP”, ”CL”, ”LOP” (such as the mode P2, P3), short press ”SET” button will display ”OP” and the corresponding time, “CL” and the corresponding time, “LOP” and the corresponding number of times; In the main interface by short press ”SET” key to see information about the parameters of the current mode, very convenient! How to set parameters? Firstly, the working mode of the module is determined; According to the working mode of the module, in the main interface (when the module is powered on, it will flash the current working mode (the default P01 mode), and then enter the main interface), ”long press the set key for 2 seconds and release” to enter the mode selection interface, and select the mode to be set by short pressing the UP and DOWN buttons (P 00 -P15); Good choice to set up the model (e.g., P03) after short press SET button to set the corresponding parameter, then to set up the parameter will be flashing (OP conduction time, CL break time, LOP cycles (” —”represents an infinite loop)), through UP and DOWN to adjust parameter values, support for long press (rapid increase or decrease) and short press 1 (increase or decrease);After setting the parameter value, select the decimal point position by pressing the STOP key and select the timing range (corresponding time: 0.1sec -999 minutes);Short press SET key to SET the next parameter of the current mode, the procedure is the same as above; Automatic sliding mode, choose good to set up the model (e.g., P15) after short press SET button to set the corresponding parameter, then to set up the parameter will be flashing (CLL disconnect time limit, CLH disconnect time limit, SP output speed (20-100%), through UP and DOWN to adjust parameter values, support for long press (rapid increase or decrease) and short press 1 (increase or decrease), timing range (the corresponding time of 0.1 seconds to 99.9 seconds).Short press SET key to set the next parameter of the current mode, the procedure is the same as above; After setting the parameters of the selected mode, press and hold the SET key for 2 seconds and then release it. The currently set mode will flash, and then return to the main interface. Setting the parameters is successful. It is very simple! Main interface: display ”000” when the module is not working (no decimal point), and it is very clear when the module is working! Mode selection screen: Long press the ”SET” key to enter, after setting is completed, long press the ”SET” key to exit back to the main screen. ”STOP” button extensions: Module enable mode: ON: The module is allowed to turn on during the OP conduction time; OFF: The module is forbidden to turn on, and it is always closed; In the main interface, short press the ”STOP” button to switch between ON and OFF, the current in which the state will flash, and then return to the main screen. (This feature is an emergency stop function, click off the MOS switch) Sleep mode: 1. ”C-L” Sleep mode: three minutes without any operation, the digital display automatically turns off, the program running as usual; 2. ”O-d” normal mode: digital display always open; Press the ”STOP” button for two seconds and then release to switch ”C-L” and ”O-d” state, in which the current state of flashes and then return to the main screen. On Jul 8, 2023 at 06:51:14 PDT, seller added the following information:

Frequently Asked Questions About DC 5V-30V MOS Trigger Cycle Timer Delay Board Switch Turn On/Off Relay Module in My Website

www.malmobeerweek.se is the best online shopping platform where you can buy DC 5V-30V MOS Trigger Cycle Timer Delay Board Switch Turn On/Off Relay Module from renowned brand(s). www.malmobeerweek.se delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.

What are the best-selling DC 5V-30V MOS Trigger Cycle Timer Delay Board Switch Turn On/Off Relay Module on www.malmobeerweek.se?