APPS TPS 98,99,00,01,02,03,04 fits Dodge Ram Cummins Diesel

$182.0 Buy It Now or Best Offer
free,30-Day Returns

Seller Store dieselautopower
(13867) 98.6%,

Location: Kaysville, Utah
Ships to: US,
Item: 304085581225

Return shipping will be paid by:Buyer
Returns Accepted:Returns Accepted
Item must be returned within:30 Days
Refund will be given as:Money back or replacement (buyer’s choice)
Return policy details:
Manufacturer Part Number:Fits Manual and Automatic Transmission Bell crank
Interchange Part Number:RAM 53031575 53031575AH 3970084 AP63428 56028184AB
Other Part Number:53031576 53031576AD 3970085 AP63427
Manufacturer Warranty:Yes
Part Brand:DieselAutoPower.com
Manual Trans part compatabilit:53031576 53031576AD 3970085 AP63427
more details:TPS APPS, Dodge Cummins
performance parts:BD, ATS, Edge, Fass, Airdog, SuperChips, MBRP

Why spend $500 from the Dealership or on ebay for a part that is equal in quality and 1/2 the price? Throttle Position Sensor/ Accelerator Position Sensor for Automatic or Manual Transmission Fits 1998.5-2004 Dodge Cummins Diesel These commercial grade sensors with a 1 year warranty. They are a direct bolt in replacement on a 24V 98.5-03 and some 04 trucks. 04 look at the engine bay picture. Note the large black plastic cover in the center of the picture. That is the APPS assembly, if you have that then this Sensor will work for you. I also have Twin Turbo kits, clamps, turbos, injectors etc. Check out my ebay store. Diesel Auto Power or Website You can save $8 on this part and 3% on any ebay purchase by signing up here https://www.mrrebates?refid=458877 If your vehicle has this vover for the TPS, this part WILL FIT. The most common problem when a APPS sensor is failing is a ”Dead Pedal” You’ll be driving down the road and hit the go pedal and NOTHING. A real annoying problem. The most common codes are the 0121,0122,222,223 code. Another issue is a surging or a bucking, this often times will not throw any codes. The other cause of the ”Dead Pedal’ is a failing vp-44 injector pump. Common codes for Injector pump are 0215,0216,1688,1689 These commercial grade sensors are a direct bolt in replacement on a 24V 98.5-03 and some 04 trucks. 04 look at the engine bay picture Take notice to the large black plastic cover in the center of the picture. That is the APPS assembly, if you have that then this Sensor will work for you. Directions below: APPS SENSOR INSTALLATION INSTRUCTIONS 1. Disconnect battery cables 2. Remove the plastic APPS cover. Next remove the six, 10 mm headed bolts that hold the bellcrank assembly on. When that is removed, you will see the sensor on the back. A T20 Torx is needed here. *Caution, these screws have loctite on them. So make sure that the bit is engaged fully into the screw head, so they do not strip, or you will need to use visegrips to remove them. NOTE: 2 new screws are provided. 3. After the old sensor is removed, take the new sensor and look at the side that bolts to the bracket. In the center, you will see the slot that engages in the tang of the bellcrank shaft. Next, line up the slot with the tang and push the sensor onto the mounting surface. *If a sensor does not mate flat to the mounting surface, the slot is not engaged properly, try again. 4. When you are sure the tang is engaged properly, rotate the sensor clockwise, until the screw holes are aligned, and start the screws. Just before the screws are tight, twist the sensor clockwise and tighten the screws. 5. Remount the bellcrank assembly to the bracket. 6. Next procedure is setting the idle voltage, using a digital voltmeter, and turning the idle stop screw clockwise. *Caution, the screw has loctite on it from factory. INCLUDED is a T20 Torx bit with a ¼ inch ratchet to turn it. Make sure the bit is engaged fully into the head before attempting to turn. Be careful not to strip the torx head! *If needed, a propane torch, VERY CAREFULLY, can be used to heat the screw; this will soften the loctite and allow it to break free. Only heat it for a couple seconds at a time and attempt to turn clockwise. Next look on the back of the 6 pin electrical connector, it is numbered. With the paperclip provided insert it into the back of the connector PIN # 3 (Green wire). Or insert it into the back of the factory plug(light blue wire w/black tracer) just make sure its PIN #3. This will get hooked to the positive lead of the voltmeter. The ground lead can be hooked to the ground terminal of the battery. Turn your voltmeter to the low voltage DC scale. Make sure paperclip does not contact ground. Proceed to plug the sensor into the factory harness and then hook the batteries up. Turn the key to the ON position. Now read the voltmeter, it should read .580-.670. Next turn the idle stop screw clockwise, NOTE you may turn for a little bit before the voltage actually rises. As soon as the voltage begins to rise, turn the screw backwards ½ turn and you are done with the idle screw. 7. Turn key off, disconnect voltmeter, and pull paperclip out of pin #3. 8. Last procedure, turn key ON, press accelerator petal slowly to the floor and then let up slowly. Turn key off. Repeat this 2 more times and you are done. Comes with Sensor and T20 Torx bit, (A Digital Voltmeter is available for $15.) On Sep-22-10 at 09:04:57 PDT, seller added the following information: Sellers: Get your own map today. Click here now. Simple. On May-11-11 at 08:49:06 PDT, seller added the following information: Sellebrity Analytics Froo www.froo | Froo Cross Sell, Free Cross Sell, Cross promote, eBay Marketing, eBay listing Apps, eBay Apps, eBay Application Shipping and Additional Information: UPS Ground/USPS Priority shipping is free to the lower 48 states, excluding Alaska, Hawaii, Puerto Rico, Guam, and all other U.S. territories. For international shipments, orders may be subject to additional duties, taxes, charges, fees, and costs associated with the shipment of the item once it has reached its destination. These charges are the buyer’s responsibility. Most orders will ship within 1 business days from the time payment is received and cleared. Shipments are not made on weekends or holidays. Express shipping is available at the buyer’s expense. Please contact us at 801-927-4600 for a shipment quote to your location. Some out of stock items are drop shipped from a distribution warehouse or directly from the manufacturer, so tracking information may not be available immediately. Tracking numbers will be updated to you as quickly as possible once an order has processed and shipped. Tracking numbers are updated manually, so please allow enough time for your information to be entered after your order has been placed. If a Core Is Required we will need to Collect the Core Before Shipping. Please watch for an Email containing Information on Payment of Core Fees/Charges Some of Our Tuners and Programmers REQUIRE a Disclaimer Form to be Filled Out, Signed, and Returned to Us Before. Shipping. Please watch for an Email containing Information on This Disclaimer Form.

Frequently Asked Questions About APPS TPS 98,99,00,01,02,03,04 fits Dodge Ram Cummins Diesel in My Website

www.malmobeerweek.se is the best online shopping platform where you can buy APPS TPS 98,99,00,01,02,03,04 fits Dodge Ram Cummins Diesel from renowned brand(s). www.malmobeerweek.se delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.

What are the best-selling APPS TPS 98,99,00,01,02,03,04 fits Dodge Ram Cummins Diesel on www.malmobeerweek.se?